Sometimes it can be difficult to come up with setup ideas. So, in the setup suggestion series of blogs, we will make recommendations for various years, makes, and models. The goal is to help those who are looking to do a setup in their vehicle but don’t know where to start (please note that these are not the only options available). 

Good 

OR  

Crossfire C7 12” Subwoofer  Sundown U 12” Subwoofer 
  • High Grade Y35 250 oz. Motor Assembly
  • 3” Aluminum Flat Wound High Temperature Hybrid Composite Voice Coil
  • Extended 6 Spoke Cast Frame
  • Sem-Pressed Paper Cone
  • Wide Roll Double Stitched Surround
  • Dual Stitched Flat XL Tinsel Lead Wires
  • Multi-Layer Nomex Spider Suspension
  • Dual 1- and 2-Ohm Voice Coil Options
  • 1,600w RMS Power Handling
  • Available In 12”, 15”, 18” Sizes
  • RMS: 1,500w
  • Aluminum 3” Voice Coil Former (Superior Heat Dissipation)
  • High Temperature Copper VC
  • Optimized High-Velocity Pole Vent
  • Tooled Cast Aluminum Vent Rings
  • High-Strenght Cast Aluminum Frame
  • D2/D4
  • Re: 3.8/6.1 Ohms
  • Fs: 42.4/40 Hz
  • Vas: 17.9/12.3 L
  • Qes: 0.30/0.38
  • Qms: 2.67/2.93
  • Qts: 0.27/0.34
  • Le: 2.41/3.67 mH
  • BL: 31.2/33.7 N/A
  • Mms: 290.2/284.5 g
  • Cms: 0.05/0.06 uM/N
  • Sense: 88.4/85.0 dB @ 1w/1m
Crossfire C7 4k Amplifier  Sundown SALT-4 Amplifier
  • Digital Class-D Strapable Mono Block Amplifier
  • Dual MOSFET PWM Power Supply
  • Stable Into 1 Ohm Mono Load
  • 24 dB / Octave, Variable Low-Pass Crossover
  • 24 dB / Octave, Variable Subsonic Filter
  • 9 dB / Octave, Variable Bass Boost
  • 180 Variable Phase Shift
  • 4 Way Protection Circuit
  • Subwoofer Level Controller Included
  • C7-2k and C7-4k Working Voltage From 8.5V ~16
  • 4,000w @ 1 Ohm Mono
  • 2,200w @ 2 Ohm Mono
  • 1,200w @ 4 Ohm Mono
  • Digital Class-D Linkable Mono Block Amplifiers
  • Dual MOS-FET PWM Power Supply
  • 1 Ohm Stable Load
  • 24 dB/Octave – Variable Low Pass Filter
  • 24 dB/Octave – Variable Subsonic Filter
  • 9 dB/Octave – Variable Bass Boost
  • 180 Degree Variable Phase Shift
  • 4 Way Protection Circuit: Thermal, Voltage, Speaker Short, and DC Offset
  • Wired Remote Control w/ Voltage & Temperature Display and Clipping Indicator
  • RMS: 800w @ 2 Ohms Linked
  • RMS: 4,000w @ 1 Ohm Mono
  • RMS: 2,000w @ 2 Ohms Mono
  • RMS: 1,000w @ 4 Ohms Mono
  • Recommended Fuse Rating: 400A
  • Low Pass Frequency Crossover: 35 Hz – 250 Hz
  • Subsonic Filter: 10 Hz – 50 Hz
  • Bass Boost – 45 Hz: 0-9 dB
  • Phase Shift Control: 0-180 Degrees
  • Input Sensitivity (+/-5%): 6 – 0.2 Volts
  • Frequency Response (+/-1 dB): 10 Hz – 250 Hz
  • Signal Noise Ration: 90 dB
  • Damping Factor: 400 <
  • Working Voltage: 9-15.5 Volts
  • T.H.D – 4 Ohms: <0.1%
  • Efficiency – 4 Ohms: 90%<
Crossfire C7-SQ 6.5” Component Speakers  Sundown SA-6.5CS v3 Component Speakers
  • Copper Pole Cap/Hybrid Composite Cone
  • 28mm Silk Dome Tweeter
  • Protective Magnet Boot
  • 100w RMS
  • Silk Dome Tweeter
  • Machine Aluminum Tweeter Housing
  • Case Aluminum Frame
  • Magnet ID Shorting Ring
  • Carbon Fiber Cone
  • Rubber Surround
  • 24 dB/Octave Crossover
  • Adjustable Tweeter Level
  • RMS: 250w (Pair)
Crossfire C5-400.4 Amplifier Sundown SALT-200.2
  • Bridgeable
  • 5 Way Protection Circuit
  • MOSFET PWM Power Supply
  • Power/Protection Indicator
  • Variable High-Pass / Low-Pass Crossover
  • 2 Ohms Stable Stereo
  • Variable 45 Hz Bass Boost
  • 4 Ohms Stable Bridged
  • 50w x 4 Channels @ 4 Ohms Stereo
  • 200w x 2 Channels @ 4 Ohms Bridged
  • Full Range Digital Amplifiers
  • High-Efficiency Digital Multi-Channel Design
  • Stable – 2 Ohm Stereo / 4 Ohm Bridged
  • 12 dB/Octave – Variable Subsonic Filter
  • 12 dB/Octave – Variable High Pass Filter
  • 12 dB/Octave – Variable Low Pass Filter
  • Crossover Multipliers – x1/x10
  • Clipping Indicator
  • 4 Way Protection Circuit: Thermal, Voltage, Speaker Short, and DC Offset
  • Optional Wired Remote Control With Voltage & Temperature Display and Clipping Indicator
  • RMS: 700w x 1 Channel @ 4 Ohm Mono
  • RMS: 325w x 2 Channels @ 2 Ohms Stereo
  • RMS: 200w x 2 Channels @ 4 Ohms Stereo
  • Recommended Fuse Rating: 60A
  • Subsonic Filter: 10 Hz – 500 Hz
  • High Pass Filter: 50 (500) Hz – 500 Hz (5 kHz)
  • High Pass Filter Multiplier: x1/x10
  • Low Pass Filter: 50 (500) Hz – 500 Hz (5 kHz)
  • Low Pass Filter Multiplier: x1/x10
  • Frequency Response (+/-1 dB): 10 Hz – 25 kHz
  • Input Sensitivity (+/-5%): 6-0.2 Volts
  • Signal Noise Ratio: 105 dB
  • T.H.D – 4 Ohms: <0.1%
  • Efficiency – 4 Ohms: 75%

Better

(2) Crossfire XT3 12″ Subwoofers 

OR  

Crossfire XT3 12” Subwoofer  Sundown X 12” Subwoofer 
  • Triple Stack 925 oz. Motor Structure Assembly
  • FEA Optimized Motor
  • Massive 3” 8 Layer Aluminum Voice Coil
  • Chrome Plated 25mm Top & Back Plate
  • Solid Hybrid Tapered Extended Pole Piece
  • Precise Circular Velocity Controlled Rear Perimeter Venting
  • Pressed Kraft Fiber Reinforced Cone
  • Multi-Layer Wide Roll Foam Surround
  • Advanced 10” Quad Layer Progressive Roll Spaced Spider Suspension
  • Dual Round XL Woven & Stitched Tinsel Leads
  • True Carbon Fiber Dustcap
  • Oversized 4 AWG Nickel Plated Push Terminals
  • Custom Tooled Embossed Motor Boot
  • Dual .5- and 1-Ohm Voice Coil Options
  • 3,000w RMS Power Handling
  • Available In 12”, 15”, and 18”
  • Fs: 35 Hz
  • Re: 2.8 Ohm
  • Qms: 8.19
  • Qes: 0.42
  • Qts: 0.4
  • Mms: 365g
  • Cms: 0.06 mm/N
  • Sd: 480 cm^2
  • Vas: 18L
  • Spl: 88.2 dB
  • BL: 24.53
  • X-Max: 34mm
  • RMS: 1,500w
  • Aluminum 3” Voice Coil Former
  • High-Tempearture Copper Voice Coil
  • Mega-Roll Surround
  • Triple Stacked Motor
  • Impedance: D2/D4
  • Re: 3.8/6.1 Ohms
  • Fs: 36.1/38.3 Hz
  • Vas: 17.1/13.2 L
  • Qes: 0.44/0.50
  • Qms: 4.89/4.92
  • Qts: 0.41/0.45
  • Le: 2.41/3.82 mH
  • BL: 25.2/30.0 N/A
  • Mms: 326.2/305.6 g
  • Cms: 0.06/0.06 uM/N
  • Sens: 84.4/84.4 dB @ 1w/1m
Crossfire XT-6k Amplifier  Sundown SALT-6 Amplifier 
  • XT-6K, 8K, Strapable Mono Block Amplifiers
  • Dual MOSFET PWM Power Supply
  • Stable Into 1 Ohm Mono Load
  • 24 dB / Octave, Variable Low-Pass Crossover
  • 24 dB / Octave, Variable Subsonic Filter
  • 9 dB / Octave, Variable Bass Boost (N/A on XS-16K)
  • 180 Variable Phase Shift
  • 4 Way Protection Circuit
  • Subwoofer Level Controller w/ Clipping Indicator Included
  • Working Voltage From 8.5V ~16V
  • 6,000w @ 1 Ohm Mono
  • 3,500w @ 2 Ohm Mono
  • 1,800w @ 4 Ohm Mono
  • Digital Class-D Linkable Mono Block Amplifiers
  • Dual MOS-FET PWM Power Supply
  • 1 Ohm Stable Load
  • 24 dB/Octave – Variable Low Pass Filter
  • 24 dB/Octave – Variable Subsonic Filter
  • 9 dB/Octave – Variable Bass Boost
  • 180 Degree Variable Phase Shift
  • 4 Way Protection Circuit: Thermal, Voltage, Speaker Short, and DC Offset
  • Wired Remote Control w/ Voltage & Temperature Display and Clipping Indicator
  • RMS: 1,200w @ 2 Ohms Linked
  • RMS: 6,000w @ 1 Ohm Mono
  • RMS: 3,000w @ 2 Ohms Mono
  • RMS: 1,500w @ 4 Ohms Mono
  • Recommended Fuse Rating: 600A
  • Low Pass Frequency Crossover: 35 Hz – 250 Hz
  • Subsonic Filter: 10 Hz – 50 Hz
  • Bass Boost – 45 Hz: 0-9 dB
  • Phase Shift Control: 0-180 Degrees
  • Input Sensitivity (+/-5%): 6 – 0.2 Volts
  • Frequency Response (+/-1 dB): 10 Hz – 250 Hz
  • Signal Noise Ration: 90 dB
  • Damping Factor: 400 <
  • Working Voltage: 9-15.5 Volts
  • T.H.D – 4 Ohms: <0.1%
  • Efficiency – 4 Ohms: 90%<
Crossfire XT-Pro 6.5” Speakers  Sundown Neo Pro 6.5” Speakers
  • Cast Aluminum Basket
  • Oversized CCAW High Temperature Voice Coil
  • Carbon Fiber Cone
  • Treated Cloth Accordion Surround
  • Push Terminals
  • 150w RMS
  • Sensitivity: 95 dB
  • Frequency Range: 80 Hz – 12 kHz
  • Voice Coil: 2”
  • Fs: 110 Hz
  • Re: 3.6/7.2 Ohms
  • Qms: 24.07
  • Qes: 0.94
  • Qts: 0.90
  • Vas: 2.85L
  • Cms: 116 uM/N
  • Rms: 0.47 kg/s
  • BL: 6.563 N/A
  • Sd: 13.3 m M
  • Xmax: 2.5mm
  • RMS: 180w
  • Neo Speaker

Best 

OR  

Crossfire XT4 12” Subwoofer Sundown ZV6 12” Subwoofer 
  • RMS: 1,500w
  • Aluminum 3” Voice Coil Former
  • High-Temperature Copper Voice Coil
  • Triple-Stacked Motor
  • Impedance: D1/D2
  • Re: 2.0/4.0
  • Fs: 33.0/35.6 Hz
  • Vas: 21.1/17.6 L
  • Qes: 0.52/0.53
  • Qms: 3.63/4.33
  • Qts: 0.46/0.47
  • Le: 0.73/1.78 mH
  • BL: 15.2/22.5 N/A
  • Mms: 291.5/298.7 g
  • Cms: 0.08/0.07 uM/N
  • Sense: 83.4/83.6 dB @ 1w/1m
Crossfire XT-8k Amplifier  Sundown SALT-8 Amplifier 
  • XT-6K, 8K, Strapable Mono Block Amplifiers
  • Dual MOSFET PWM Power Supply
  • Stable Into 1 Ohm Mono Load
  • 24 dB / Octave, Variable Low-Pass Crossover
  • 24 dB / Octave, Variable Subsonic Filter
  • 9 dB / Octave, Variable Bass Boost (N/A on XS-16K)
  • 180 Variable Phase Shift
  • 4 Way Protection Circuit
  • Subwoofer Level Controller w/ Clipping Indicator Included
  • Working Voltage From 8.5V ~16V
  • 8,000w @ 1 Ohm Mono
  • 4,800w @ 2 Ohms Mono
  • 2,600w @ 4 Ohms Mono
  • Digital Class-D Linkable Mono Block Amplifiers
  • Dual MOS-FET PWM Power Supply
  • 1 Ohm Stable Load
  • 24 dB/Octave – Variable Low Pass Filter
  • 24 dB/Octave – Variable Subsonic Filter
  • 9 dB/Octave – Variable Bass Boost
  • 180 Degree Variable Phase Shift
  • 4 Way Protection Circuit: Thermal, Voltage, Speaker Short, and DC Offset
  • Wired Remote Control w/ Voltage & Temperature Display and Clipping Indicator
  • RMS: 16,000w @ 2 Ohms Linked
  • RMS: 8,000w @ 1 Ohm Mono
  • RMS: 4,000w @ 2 Ohms Mono
  • RMS: 2,000w @ 4 Ohms Mono
  • Recommended Fuse Rating: 800A
  • Low Pass Frequency Crossover: 35 Hz – 250 Hz
  • Subsonic Filter: 10 Hz – 50 Hz
  • Bass Boost – 45 Hz: 0-9 dB
  • Phase Shift Control: 0-180 Degrees
  • Input Sensitivity (+/-5%): 6 – 0.2 Volts
  • Frequency Response (+/-1 dB): 10 Hz – 250 Hz
  • Signal Noise Ration: 90 dB
  • Damping Factor: 400 <
  • Working Voltage: 9-15.5 Volts
  • T.H.D – 4 Ohms: <0.1%
  • Efficiency – 4 Ohms: 90%<
Crossfire C5-800.4 Amplifier  Sundown SALT-400.2 
  • Bridgeable
  • 5 Way Protection Circuit
  • MOSFET PWM Power Supply
  • Power/Protection Indicator
  • Variable High-Pass / Low-Pass Crossover
  • 2 Ohms Stable Stereo
  • Variable 45 Hz Bass Boost
  • 4 Ohms Stable Bridged
  • 100w x 4 Channels @ 4 Ohms Stereo
  • 400w x 2 Channels @ 4 Ohms Bridged
  • Full Range Digital Amplifiers
  • High-Efficiency Digital Multi-Channel Design
  • Stable – 2 Ohm Stereo / 4 Ohm Bridged
  • 12 dB/Octave – Variable Subsonic Filter
  • 12 dB/Octave – Variable High Pass Filter
  • 12 dB/Octave – Variable Low Pass Filter
  • Crossover Multipliers – x1/x10
  • Clipping Indicator
  • 4 Way Protection Circuit: Thermal, Voltage, Speaker Short, and DC Offset
  • Optional Wired Remote Control With Voltage & Temperature Display and Clipping Indicator
  • RMS: 1,300w x 1 Channel @ 4 Ohm Mono
  • RMS: 650w x 2 Channels @ 2 Ohms Stereo
  • RMS: 400w x 2 Channels @ 4 Ohms Stereo
  • Recommended Fuse Rating: 100A
  • Subsonic Filter: 10 Hz – 500 Hz
  • High Pass Filter: 50 (500) Hz – 500 Hz (5 kHz)
  • High Pass Filter Multiplier: x1/x10
  • Low Pass Filter: 50 (500) Hz – 500 Hz (5 kHz)
  • Low Pass Filter Multiplier: x1/x10
  • Frequency Response (+/-1 dB): 10 Hz – 25 kHz
  • Input Sensitivity (+/-5%): 6-0.2 Volts
  • Signal Noise Ratio: 105 dB
  • T.H.D – 4 Ohms: <0.1%
  • Efficiency – 4 Ohms: 75%
Crossfire XS-ST1 Tweeters  Sundown BT-R1 Tweeters
  • Precision CNC Aluminum Horn Tweeter
  • Chambered Neodymium Motor
  • Aluminum Diaphragm w/ 1” CCA Voice Coil
  • Capacitor Included With Tweeter For Proper Frequency Cutoff
  • Frequency Response: 2800Hz – 28 kHz
  • Sensitivity: 106 dB
  • Power Handling: 50w RMS
  • Impedance: 4 and 8 Ohm
  • 3” Super Tweeter
  • 100w RMS
Euro_Bass (Maggie's) MK6 Crossfire Jetta 2021 Walkthrough

About The Author euro_bass

comments (0)

Your email address will not be published.

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>